Beginner's Plumbing: The Essentials for Bathtub Installation
Beginner's Plumbing: The Essentials for Bathtub Installation
Blog Article
What're your thoughts about Installing A Bathtub?
Mounting a bath tub isn't specifically rocket science, but it does require strong plumbing, woodworking, as well as often, tiling abilities. Changing an old bath tub with a new one is also a reasonably challenging project. If the old bathtub is conveniently available, the project can relocate rapidly; if you need to open a wall surface to eliminate the old bathtub and place the new tub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to move out the old tub and set in the new one. Make sure you have qualified yourself for the work and are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed task, it is far better to think about employing one prior to you start. Possibilities are you may need a professional plumber to make tube links.
This write-up will assist you mount a brand-new tub in your washroom if you have currently purchased a new bathtub and also don't need to transform the arrangement of your previous water supply pipelines.
Your tools as well as product list must make up the following:
Getting ready for the Setup
To start with, the sustaining structure provided with the bath needs to be fitted (if called for) according to the maker's instructions. Next, fit the taps or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the tap includes a plastic washer, it is fitted in between the bath and the faucets. On a plastic bath, it is additionally practical to fit a supporting plate under the taps device to stop strain on the tub.
Fit the versatile tap ports to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. See to it you use every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bath need to now prepare to be suited its last setting.
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you ought to do is separate the supply of water. After doing so, switch on the taps to drain any type of water remaining in the system. The procedure of eliminating the existing taps can be rather bothersome because of the limited access that is usually the situation.
Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipelines to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been gotten rid of, use the very same device to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from turning throughout this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing compound.
Prior to going on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new taps to fit.
Installing the Bath tub
Utilizing both wood boards under its feet, put the bathtub in the required placement. The wood boards are practical in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next objective is to make sure that the tub is leveled all round. This can be attained by inspecting the spirit level and also adjusting the feet on the bath tub until the spirit level reads level.
To install taps, fit all-time low of the outermost versatile faucet port to the ideal supply pipe by making a compression join; then do the same for the various other faucet.
Turn on the water and also check all joints and also brand-new pipework for leaks as well as tighten them if necessary. Load the bath tub as well as also inspect the overflow electrical outlet and also the typical electrical outlet for leaks.
Lastly, deal with the bathroom paneling as described in the maker's user's manual. Tiling and also securing around the bath tub should wait till the bath tub has actually been used at the very least once as this will certainly resolve it right into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the installing opening in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Safeguard the faucet in place with the producer supplied backnut. When the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The previous type ought to be connected to the tap ends first, tightening up only by hand. The supply pipes can later on be linked to the various other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the area where the bath meets the tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split a stiff seal, causing the water to penetrate the wall surface in between the bath as well as the tiling, leading to complications with wetness and also feasible leaks to the ceiling below.
You can select from a variety of coloured sealers to blend in your components as well as installations. They are offered in tubes as well as cartridges, and are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger space to fill up, you can fill it with twists of soaked paper or soft rope. Keep in mind to always load the bath tub with water prior to securing, to enable the activity experienced when the bathtub is in use. The sealant can split rather very early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is advisable to fit the floor tiles utilizing water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that blog entry about A Step-by-Step Guide to Installing a Bathtub when doing research the search engines. Don't hesitate to set aside a second to distribute this write-up if you enjoyed reading it. I value reading our article about How to Install a Bathtub Yourself.
Plumbing emergency? We're ready. Report this page